The 3rd generation high performance ESC & Flight controller combo from Hobbywing. The Hobbywing XRotor 4in1 60A ESC & FC G3 Combo is the combination of a Hobbywing XRotor Micro 60A 4in1 Blheli_32 ESC and a Hobbywing XRotor F4 G3 Flight Controller. The ESC & FC stack together forming an all in one stack. The Hobbywing XRotor ESC is rated at 60A continuous and 80A burst. The XRotor G3 Flight Controller is an F4 based board with integrated OSD and SD card slot for logging.
Onboard 12V BEC
FMU integrates with 12V BEC circuit. It can supply regulated 12V power for FPV gear.
Onboard Pit Switch Module
FMU integrates with Pit Switch module. You can use your transmitter to turn on and off the your VTX power.
The innovative connecting method via a JST cable combined with the vibration isolation grommets reduces the impact on high sensitivity FC components making every flight more stable and precise.
SD card Supported
An SD card can be inserted into the FC to record and save more flight data,
which allows users to adjust their aircraft easily.
- XRotor Flight Controller F4
- Firmware Target: OmnibusF4SD
- Size: 36x36mm/30.5x30.5mm mounting
- Supports VBAT & CRT monitoring (Voltage & Current)
- Supports: Betaflight/Cleanflight
- OSD: Built-in
- Size: 35x35mm
- Weight: 6g
Highly Integrated & Compact
The 4-in-1 ESC not only includes 4 high-performance 60A ESCs, 1 built-in 5V BEC (0.6A) but also an Amp/Volt monitoring port which allows FC to monitor the volt & amp in real time (on condition that the FC supports this function); it’s as small as a FC for FPV(s) and easy for installation and wiring. With the remarkably small size, it's a perfect match for competition FPV(s).
The use of 32 Bit ARM MCUs with the operating frequency of up to 48MHz, imported high quality MOSFETs, 3-in-1 drive ICs and ceramic capacitors, 3-ounce copper, and 6 layers of PCBs guarantees less heat, higher efficiency and rapider response.
BLHeli_32 Firmware Ready
The XRotor 60A ESC includes BLHeli_32 firmware and support paramater changes and firmware updates.
Besides the regular PWM mode, Oneshot125/Oneshot42/Multishot modes, the latest DShot150/300/600/1200 modes are also supported. In DShot150/300/600/1200 modes, the ESC has great anti-interference performance and rapid response. DShot 1200 mode features great anti-interference & rapid response.
Hardware Generated PWM & Damped Light Mode
The ESC firmware uses hardware generated motor pwm for smooth throttle response and silent operation. Damped light does regenerative breaking, causing very fast motor retardation, and it inherently also does active freewheeling.
- XRotor Micro 60A 4in1 ESC BLHeli_32
- Continuous/Peak Current: 60x4 / 80Ax4
- Size: 30.5x30.5mm mounting
- Lipo Cells: 3-6S
- Bec Output: 5V 0.6A
- Input Wires: Red-12AWG-130mm / Black-12AWG-130mm
- Output Wires: No wires but solder tabs
- Firmware: BLHeli_32
- Weight: 15g
- 1x XRotor Micro 60A BLHeli_32 4in1 ESC (3-6S)
- Pre-installed capacitor (needed, don't remove)
- 1x Hobbywing G3 FC
- Cables (XT60 + input wires)
- 1x XRotor Manual