Power Distribution

Lumenier Mini 4Power + Plus PDB 20x20mm (5v/8v Reg, 100A Curr.)

The Lumenier Mini 4Power + Plus PDB (20x20mm, 5v/8v Reg, 100A Curr.) (3-5s)

£10.72 £6.00

Lumenier 4Power Quick Swap Power Distribution Board

The Quick Swap PDB enables solder-less arm connections with ESC power being routed into specially designed power taps and the ESC Servo connection being made available on the side underneath the power connection.

£17.14 £13.80

Matek FCHUB-6S with 184A Current Sensor PDB

The FCHUB power distribution board features a 184A current sensor and 5V & 10V filtered DC voltage output.

£6.40

Matek FCHUB-A5 with 184A Current Sensor PDB

The FCHUB-A5 features a 184A current sensor and 5V & 10V filtered DC voltage output.

£5.40

Matek FCHUB-VTX 25-500mW VTX with 184A Current Sensor PDB

FCHUB Series, 6~27V Input PDB w/ current sensor 184A, 40CH & 25/200/500mw switchable VTX , Traditional button+LED control, BFCMS control via FC Uart_TX, Ribbon cable connection with FC F405-OSD.

£23.95

Matek FCHUB-W PDB For Fixed Wing

The Matek FCHUB-W is a Special PDB designed for Fixed Wing with 4x BEC & onboard current sensor.

£10.95

Matek HUBOSD eco H-Type PDB

The HUBOSD eco H-Type with STOSD8 140A Current Sensor and Dual BEC from Matek Systems.

£12.28

Matek HUBOSD eco X-Type PDB

The HUBOSD eco X-Type with STOSD8 140A Current Sensor and Dual BEC from Matek Systems.

£12.28

Matek HUBOSD SE PDB

The HUBOSD SE with STOSD8 184A Current Sensor and Dual BEC from Matek Systems.

£13.73

Matek Linear Regulator 4S LiPo to 12V 300mA

Generally the input voltage of FPV cameras is 7~13V - with a 4S LiPo input, the Matek linear regulator can convert 14~17V to 12V, and power camera and/or 12V 1W LEDs without ripples or noise.

£3.00

Matek Micro BEC 5V/12V Adjustable

The Matek micro BEC is a high efficiency rectified step-down switch mode converter. It offers a very compact solution to achieve 1.5A continuous output current over a wide input supply range.

£3.00

Matek Mini Power Hub V3 PDB (5V & 12V BEC)

The Matek Mini Power Hub V3 PDB offers regulated 5V and 12V BEC outputs and a camera/VTX hub with voltage selectors all in a familiar 36mm square form factor - ideal for stacking below your flight controller (Naze32, CC3D, etc.).

£4.44

Matek XT60 PDB (5V & 12V BEC)

The Matek XT60 PDB offers regulated 5V and 12V BEC outputs in a familiar 36mm square form factor - ideal for stacking below your flight controller (Naze32, CC3D, etc.).

£4.44

Matek XT60 PDB XPW (5V & 12V BEC + 140A Current Sensor)

The PDB-XPW distributes power from a LiPo pack to 4 ESCs as well as providing syncronised & regulated DC 5V outputs and linear regulated DC 12V for powering cameras, VTXs etc.

£5.88

Mini 5V BEC 3A

This little circuit board may look tiny but inside is a high efficiency DC/DC step-down converter which can output up to 3 Amp at 5V without the need of any heat-sink or forced cooling.

£4.35

Pololu 12V 600mA Step Down Voltage Regulator (D24V6F12)

The compact (0.4″ × 0.5″) D24V6F12 switching step-down (or buck) voltage regulator takes an input voltage between 15 V and 42 V and efficiently reduces it to 12 V while allowing for a maximum output current of 600 mA.

£5.92