Overview:
The SpeedyBee F405 Wing Mini is a compact, fixed wing flight controller features a wide array of features. The F405 is small yet mighty and doesn't compromise in functionality. The clever design suits models from compact gliders to sub 250g fixed wing planes. Via the SpeedyBee App the F405 Mini enabled graphical setup and tuning, making initial setup of models very easy. The F405 Mini features all the normal connectors you would expect including connectors for GPS & FPV cameras with pads broken out on the rear of the ports should you wish to hard solder. The F405 Mini features the new wireless tuning V2 for a smoother, more reliable tuning experience. The flight controller features dual camera switching for analogue cameras and 6 uart ports to connect peripherals. The board also features 11 PWM outputs for motor and servo control. Compatibility has been maintained for both Ardupilot and INAV software.
SpeedyBee F405 WING Mini FC board:
- MCU STM32F405, 168MHz, 1MB Flash
- IMU(Gyro&Accelerometer) ICM-42688-P
- Barometer SPL006-001
- OSD Chip AT7456E
- Blackbox MicroSD Card Slot
- UART 6 sets (USART1, USART2, USART3, UART4, UART5,
- UART6 - Dedicated for Wireless board Telemetry connection)
- I2C 1x Used for magnetometer, digital airspeed sensor
- ADC 4x (VBAT, Current, Analog RSSI, Analog AirSpeed)
- PWM 12x (9x pin headers + 2x solder pads + 1x "LED" pad)
- ELRS/CRSF Receiver Supported, connected to UART1
- SBUS Built-in inverter for SBUS input (UART2-RX)
- LED 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red)
- Analog RSSI Supported, Named as "RS"
- Dual Analog Camera Switching Default to Camera1 Video Input (C1). Switch between C1 and C2 using ArduPilot - Relay or INAV Modes/USER.
- Both cameras should have the same video format, either PAL or NTSC.
- Supported FC Firmware INAV: SpeedyBeeF405WING (default)
- ArduPilot: SpeedyBeeF405WING
- Weight 5.6g
SpeedyBee F405 WING Mini PDB board:
- Input voltage range 7~26V (2~6S LiPo)
- Battery Voltage Sensor Connect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
- Battery Current Sensor 80A continuous, 150A peak Connect to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)
- TVS Protective diode Yes
- FC BEC output Output 5.2V +/- 0.1V DC Continuous current 2 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed Sensor, Telemetry module
- VTX & Camera power supply The VTX power interface Vv offers two power supply options: direct battery voltage or integrated BEC 5V (sharing the 5V4A Servo BEC voltage)
By default, it is set to battery voltage
(Ensure the VTX and camera input voltage range is compatible)
Switching to 5V power supply is possible via pad jumper (using Servo BEC output)
(If using this method, ensure the current requirements for both servo and VTX are sufficient)
- Servo BEC output Output 5V +/- 0.1V DC Continuous current 4 Amps, 5A Peak Voltage adjustable, 5V Default, 6V via jumper Designed for Servos.
- Weight 5.5g
SpeedyBee F405 WING Wireless board:
- Wireless Configuration (long press BOOT button for 6 seconds to switch modes)
- USB Port Type Type-C
- Buzzer 5V Active Buzzer
- Weight 3.2g
Includes:
1x SpeedyBee F405 WING Mini Flight Controller
Accessories
