Give your build a super clean professional look with this wire covering. Simply pull the strands out of the centre, seal the ends with a flame to stop them fraying and finish with heatshrink. Perfect for those extra special builds.
Give your build a super clean professional look with this wire covering. Simply pull the strands out of the centre, seal the ends with a flame to stop them fraying and finish with heatshrink. Perfect for those extra special builds.
Give your build a super clean professional look with this wire covering. Simply pull the strands out of the centre, seal the ends with a flame to stop them fraying and finish with heatshrink. Perfect for those extra special builds.
Give your build a super clean professional look with this wire covering. Simply pull the strands out of the centre, seal the ends with a flame to stop them fraying and finish with heatshrink. Perfect for those extra special builds.
Give your build a super clean professional look with this wire covering. Simply pull the strands out of the centre, seal the ends with a flame to stop them fraying and finish with heatshrink. Perfect for those extra special builds.
Give your build a super clean professional look with this wire covering. Simply pull the strands out of the centre, seal the ends with a flame to stop them fraying and finish with heatshrink. Perfect for those extra special builds.
Give your build a super clean professional look with this wire covering. Simply pull the strands out of the centre, seal the ends with a flame to stop them fraying and finish with heatshrink. Perfect for those extra special builds.
This medium strength thread locker and sealant should easily see you through 2-3 quad builds. Ideal for stopping motor and frame screws from working themselves loose.
We use a slightly higher percentage of tin compared with the classic 60/40 offered in most hobby stores. This allows for a lower melting point making soldering, and especially desoldering equipment less risky for your gear.
This Engineer SS-02 Solder Sucker desoldering pump is a very high quality solder sucker - made in Japan and with a flexible heat resistant silicone tip.
The ETHIX GoPro Strap comes with a very sticky coating formula not found in many straps. This makes it perfectly suited for locking down your GoPro. Also works for batteries, obviously!
The ETHIX Cable Set contains the most commonly used wire sizes used when building a multiCopter and this affordable cube like device makes your life just that much easier.
This is a new sensor designed and developed by FrSKY to collect important flight information and performance data which can then be transmitted via the SMART PORT of telemetry-enabled receivers such as X8R, X6R, X4R, etc to a Taranis Transmitter.
The FrSky GPS Sensor feeds variable directional information such as altitude, position, speed, and UTC time, which is displayed in real time on FrSky’s Taranis transmitter.
The FrSky STK USB programming adapator can be used for upgrading the firmware on FrSKY receivers or for programming the settings on the S6R/S8R receivers.
The FrSky Variometer sensor calculates the altitude from atmospheric pressure. Atmospheric pressure will get lower as you go up in altitude, using this the sensor will estimate the altitude.
The HobbyRC easy prop nut removal tool is a compact tool that makes it easy to swap out your props. Smaller than a spanner or nut driver, this is a must have for anyone's field kit.
The HobbyRC battery strap is just the right length for most mini quad batteries while the rubberised reverse grips your battery and helps to stop it sliding back and forth in flight.
Matek vibration isolation standoffs now available for Micro builds in M2 size. The rubber standoffs help to reduce vibrations passing through to your flight controller gyro.
The Matek tail light with 8x WS2812B LEDs & Loud Buzzer provides two control modes. It can be controlled by Flight Controller(Cleanflight/Betaflight) or Transmiter.
This Panasonic 1000uF Ultra Low ESR 25V electrolytic capacitor is ideally suited to 4S voltages, used as a main filtering capacitor where power enters your quad (PDB or 4in1).
This Panasonic 1000uF Ultra Low ESR 35V electrolytic capacitor is ideally suited to 6S voltages, used as a main filtering capacitor where power enters your quad (PDB or 4in1).
The SpeedyBee USB to Bluetooth adapter allows remote in the field programming of Betaflight flight controller settings over bluetooth on your mobile phone or tablet.
Current sensor for the TBS CORE (Team black sheep). This is the 100A version. It's compatible with other OSDs as well although we can't take responsibility for that.
TBS Race Wire is the perfect upgrade for your racing or freestyle rig. It simply replaces a section of your motor wires under the tips of the propeller which makes your quad immune to prop strike damage.
TBS Race Wire mini is the perfect upgrade for your racing or freestyle rig. It simply replaces a section of your motor wires under the tips of the propeller which makes your quad immune to prop strike damage.